Оборудование для автоматизации Системы умный дом
Диммер DMG 2 T KNX, базовый модуль линейки MIX2, 2-канальный, универсальный, для всех типов ламп
Код товара: 47428
Артикул: TN:4930270
Диммер DMG 2 T KNX, базовый модуль линейки MIX2, 2-канальный, универсальный, для всех типов ламп
Цену уточняйте
*Цены на сайте не являются офертой и носят ознакомительный характер, для уточнения актуальности цены вы можете связаться с оператором.
DMG 2 T KNX Базовый модуль MIX2. Двухканальный универсальный диммер для всех типов ламп. Также подходит для управления вентиляторами. Позволяет подключать до 2-х модулей расширения из линеек MIX и MIX2. Автоматическое распознавание типа нагрузки. Выходы: 2 x 400 Вт/ВА или 1 x 800 Вт/ВА. Установка на ДИН-рейку. 10мА (с двумя модулями расширения)
2-way universal dimmer actuator MIX2
Basic module MIX2
Can be upgraded to maximum of 6 channels
For dimming dimmable LED, incandescent lamps, LV, HV halogen lamps and energy saving lamps
Also suitable for dimming of dimmable energy-saving lamps
Also suitable for controlling fans
Up to two extension modules MIX or MIX2 can be connected to one basic module
Device and KNX bus module can be swapped independently of each other
Removable KNX bus module enables devices to be changed without reprogramming
Manual set-up and use of switching actuators is possible without KNX bus module
LED switching status display for each channel
Manual operation on device (even without bus connection)
Dimming output: 400 W/VA per channel or 800 W/VA in parallel operation
If the DMB 1 T KNX 'Dimbooster' is used, the dimming output can be upgraded to 300 W/VA. Output to a maximum of 2000 W/VA by using max. 4 boosters possible
Automatic load detection (can be deactivated)
For R, L and C loads
Operating voltage KNX Bus voltage, 10 mA
Operating voltage 230 V AC
Frequency 50 Hz
Stand-by consumption 0,9 W
Width 4 modules
Installation type DIN rail
Type of connection Screw terminals
Max. cable cross section Solid wire: 0.5 mm ( 0.8) to 4 mm | Stranded wire with end sleeve: 0.5 mm to 2.5 mm
Number of channels 2
Lamp types Incandescent, low-voltage and high-voltage halogen and dimmable energy saving lamps and LED
Switching capacity per channel 400 W
Switching capacity in parallel operation 800 W
Switching capacity dimmable energy saving lamps per channel 80 W
Switching capacity dimmable energy saving lamps in parallel operation 140 W
Switching capacity dimmable 230 V LED per channel 60 W
Switching capacity dimmable 230 V LED in parallel operation 120 W
Switching capacity min. 5 W
Max. cable length 100 m
Ambient temperature -5 °C … +45 °C
Type of protection IP 20
Protection class II according to EN 60 669
2-way universal dimmer actuator MIX2
Basic module MIX2
Can be upgraded to maximum of 6 channels
For dimming dimmable LED, incandescent lamps, LV, HV halogen lamps and energy saving lamps
Also suitable for dimming of dimmable energy-saving lamps
Also suitable for controlling fans
Up to two extension modules MIX or MIX2 can be connected to one basic module
Device and KNX bus module can be swapped independently of each other
Removable KNX bus module enables devices to be changed without reprogramming
Manual set-up and use of switching actuators is possible without KNX bus module
LED switching status display for each channel
Manual operation on device (even without bus connection)
Dimming output: 400 W/VA per channel or 800 W/VA in parallel operation
If the DMB 1 T KNX 'Dimbooster' is used, the dimming output can be upgraded to 300 W/VA. Output to a maximum of 2000 W/VA by using max. 4 boosters possible
Automatic load detection (can be deactivated)
For R, L and C loads
Operating voltage KNX Bus voltage, 10 mA
Operating voltage 230 V AC
Frequency 50 Hz
Stand-by consumption 0,9 W
Width 4 modules
Installation type DIN rail
Type of connection Screw terminals
Max. cable cross section Solid wire: 0.5 mm ( 0.8) to 4 mm | Stranded wire with end sleeve: 0.5 mm to 2.5 mm
Number of channels 2
Lamp types Incandescent, low-voltage and high-voltage halogen and dimmable energy saving lamps and LED
Switching capacity per channel 400 W
Switching capacity in parallel operation 800 W
Switching capacity dimmable energy saving lamps per channel 80 W
Switching capacity dimmable energy saving lamps in parallel operation 140 W
Switching capacity dimmable 230 V LED per channel 60 W
Switching capacity dimmable 230 V LED in parallel operation 120 W
Switching capacity min. 5 W
Max. cable length 100 m
Ambient temperature -5 °C … +45 °C
Type of protection IP 20
Protection class II according to EN 60 669
Техническое описание
pdf, 231.19 Кбайт
